Multifunctional Horizontal Automatic Carton Packing Machine

ZH-520

L350-600mm
W200-400mm
H200-350mm

5-12 cartons/min.

Top loading

70

Adhesive tape/ Melt adhesive

4 kw

380V 50Hz 3

3000Kg

4000 x 930 x 1370mm

Cartoning machine is a packaging machine which form a carton board blank into a carton, filled with a product or bag of products or number of products into single carton via robot, after the filling, the machine close both the ends of carton completely sealing the carton.
All our cartoning solutions are designed to improve productivity for our customers with easy-to-use equipment that can increase output while reducing labor cost.

The cartoning machine system consists of three modules: unpacking module, robot hand filling module, sealing module, etc. The
modules can be freely combined to meet the customized needs of customers.
The system can meet the requirements of regular shape items such as food, household paper, etc., as well as special-shaped
products such as pillow bag packaging, gusset bag packaging, etc.
The storage tank for folded carton is big and can be increased the storage tank position according to customer requirements.
With intelligent control system of HMI , effective monitoring of equipment operation and fault prompts, easy to operate

(1) Clean the machine each time after packaging.
(2) Turn off the power before cleaning the machine to low the temperature of heating part.
(3) Never spray the water or steam directly on the machine when cleaning.
(4) Main components to be cleaned:
*Remove the product chips store up in the conveyance line of the product by compressed air or in other way.
*Brush off the film chips adhered to the sealing surface by the wire brush applied with the silicone oil.
*Clear the dirt on the control panel, safety cover and operating surface by a piece of soft cloth.
*Conductive ring of the mid sealing tool and end sealers: clean it once a week or two weeks. Clean the conductive ring by the back
of the sandpaper with the master power off.

2. Maintenance and clean for machine every month.
(1) Apply the lubricating grease on the bearing of the end sealers.
(2) Apply the lubricating grease on the gear and chain (pulley) of the driving unit.
(3) Check the tightness of the chain and belt of the driving unit, and tighten the loosed one.
(4)Check the tightness of the fastening screw or nut of all parts, and tighten the loosed one.

3. Relevant inspection for machine once a half year.
(1) Check the wear intensity of the belt of the driving unit, and replace the worn-out one.
(2) Check the wear intensity of the rubber roller, and replace the one affecting the film advancing effect.
(3) Properly adjust the brake unit of the film-carrying roller.
(4) Check all wearing parts, and immediately replace the damaged one.
(5) Check the fastness of the wiring on the electrical terminal plate, and tighten the loosed one. Check the inverter,
programmable controller and circuit board, and remove the dust or dirt on them by the compressed air.

4. Maintenance and clean for machine every day or every shift.
(1) Clean the machine each time after packaging.
(2) Turn off the power before cleaning the machine to low the temperature of heating part.
(3) Never spray the water or steam directly on the machine when cleaning.
(4) Main components to be cleaned:
*Remove the product chips store up in the conveyance line of the product by compressed air or in other way.
*Brush off the film chips adhered to the sealing surface by the wire brush applied with the silicone oil.
*Clear the dirt on the control panel, safety cover and operating surface by a piece of soft cloth.
*Conductive ring of the mid sealing tool and end sealers: clean it once a week or two weeks. Clean the conductive ring by the back
of the sandpaper with the master power off.

5. Maintenance and clean for machine every month.
(1) Apply the lubricating grease on the bearing of the end sealers.
(2) Apply the lubricating grease on the gear and chain (pulley) of the driving unit.
(3) Check the tightness of the chain and belt of the driving unit, and tighten the loosed one.
(4)Check the tightness of the fastening screw or nut of all parts, and tighten the loosed one.

6. Relevant inspection for machine once a half year.
(6) Check the wear intensity of the belt of the driving unit, and replace the worn-out one.
(7) Check the wear intensity of the rubber roller, and replace the one affecting the film advancing effect.
(8) Properly adjust the brake unit of the film-carrying roller.
(9) Check all wearing parts, and immediately replace the damaged one.
Check the fastness of the wiring on the electrical terminal plate, and tighten the loosed one. Check the inverter, programmable
controller and circuit board, and remove the dust or dirt on them by the compressed air.